Shelterseal 5000HD Membrane

 

Cold application – installed without the use of open flames

Slip free surface – membrane provides an ideal safe

working surface

Ideal for parking decks and car parks vehicular traffic

structures and also expansion joints

SAFETY PRECAUTIONS

ARDEX WPM 5000HD is hazardous; non-dangerous goods.

Wear eye/face protection. Use only in well ventilated

areas. Keep rolls in a well ventilated place. In case of

contact with eyes rinse with plenty of water and contact a

doctor or Poisons Information Centre.

ARDEX WPM 249 is hazardous; non-dangerous goods. It is

highly flammable harmful if swallowed and irritating to the

eyes and skin. Keep away from sources of ignition. No

smoking. Keep container tightly closed and in a well

ventilated place.

ADDITIONAL INFORMATION FOR ARDEX WPM 249 IS

FOUND IN THE MATERIAL SAFETY DATA SHEET.

STORAGE

All rolls of ARDEX WPM 5000HD whether palletised or

loose should be stored in a cool covered area protected

against sunlight and UV radiation. Rolls should be stored in

a vertical position on a smooth floor so as not to damage

the edges.

ADDITIONAL INFORMATION IS LISTED IN THE MATERIAL

SAFETY DATA SHEET.

PACKAGING

Roll size: 1m x 20m

Roll weight: Approx 30kg.

Other products: ARDEX Shelterseal Primer 5 litres and

20 litres.

Rolls per pallet: 25

 

TECHNICAL PERFORMANCE DATA

Properties Typical Values Test Method

Thickness 1.5mm UNI 8202

Weight 1.6kg UNI 8202

Colour Black

Softening point 110?C

Temperature

resistance (max.) 150?C

Tensile strength

Longitudinal 152kg/8cm

Transverse 124kg/8cm

Elongation (longitudinal) 32% ASTM D638

Elongation (transverse) 21% ASTM D638

Tearing

Longitudinal 350N UNI 8202/9

Transverse) 300N UNI 8202/9

Adhesion

To primed concrete 4.9 N/mm ASTM D1000

To steel 5.8 N/mm ASTM D1000

Puncture resistance 220 N/65mm ASTM E96

Vapour transmission

rate 0.3g/m/24hrs ASTM E96

Cold flexibility -30?C ASTM D146

 

ARDEX WPM 5000HD is hazardous; non-dangerous goods. Wear eye/face protection. Use only in well ventilated areas. Keep rolls in a well ventilated place. In case of contact with eyes rinse with plenty of water and contact a doctor or Poisons Information Centre.

ARDEX WPM 249 is hazardous; non-dangerous goods. It is highly flammable harmful if swallowed and irritating to the eyes and skin. Keep away from sources of ignition. No smoking. Keep container tightly closed and in a well ventilated place.

ADDITIONAL INFORMATION FOR ARDEX WPM 249 IS FOUND IN THE MATERIAL SAFETY DATA SHEET.

 

 

PRODUCT DESCRIPTION

ARDEX WPM 5000HD (Shelterseal 5000 HD Self Adhesive

Membrane) is an industrial strength “peel and stick”

bituminous/asphalt membrane. ARDEX WPM 5000HD is

reinforced with a layer of polypropylene mesh giving the

product exceptionally high mechanical characteristics.

ARDEX WPM 5000HD is made from two structural

components:

• Bitumen/asphalt compound modified with SBS and

high tack resins.

• A protective polypropylene mesh hot laminated to

the bituminous/asphalt compound. This gives the

membrane its mechanical and physical characteristics

such as heat and shape stability chemical and puncture

resistance.

FEATURES/BENEFITS

Cold Application

Installed without the use of open flames. Ideal for

installation in restricted spaces.

High durability

Polypropylene mesh reinforcement layer provides tough

puncture resistant finish.

Constant thickness

The membrane is manufactured using the highest quality

materials standards and sheet manufacturing techniques.

Slip free surface

Membrane provides an ideal safe working surface.

ACCEPTABLE SUBSTRATES

• Concrete renders and screeds

• Fibre cement sheets

• Structural or marine plywood

For use over other substrates including existing

membranes contact ARDEX.

TYPICAL APPLICATIONS

• Parking decks & car parks

• Vehicular traffic structures

• Expansion joints

• Underneath clay tiles or asphalt shingles

• Any applications where the waterproofing must have

high mechanical characteristics

 

 

 

BASIC APPLICATION INSTRUCTIONS

Surface Preparation

Surfaces to which the ARDEX WPM 5000HD is to be

installed must be properly prepared prior to installation. All

surfaces must be clean dry smooth free of sharp edges

loose or foreign materials oil grease and other materials

that may damage the membrane. If concrete has moisture

on surface use gas torch to dry and warm before priming

or apply 1 coat of ARDEX WPM 300 at a coverage rate

of 3.0m2 per L and allow to cure for at least 3 days prior

to proceeding.

Priming

Prior to the application of the membrane all prepared

surfaces should be primed with ARDEX WPM 249

(Shelterseal Primer) at a rate of 5-6m2 per litre and allowed

to dry.

Application of ARDEX WPM 5000HD

ARDEX WPM 5000HD should always be applied from the

lowest point to enable laps to shed water. All edge and end

laps must be overlapped a minimum of 60mm. Internal and

external corners shall be reinforced with an extra layer of

membrane 300mm wide. All end laps and exposed edges

shall be sealed with a bead of Self Adhesive Mastic.

On vertical surfaces the installation should start at the

lowest point with the joints overlapping by at least 100mm

and formed so that they will shed water. All rolls of ARDEX

WPM 5000HD are marked with a 60mm line for overlapping.

Ensure that the membrane is properly adhered to the

surface at perimeters or around penetrations.

On completion of the installation of ARDEX WPM 5000HD

it is necessary that protection board be used before back

filling to protect the membrane from damage.

Under no circumstances should the membrane be left

exposed to UV light for long periods.

Applying asphalt directly over ARDEX WPM 5000HD.

The asphalt should be applied as soon as possible after

the Shelterseal membrane has been installed. ARDEX

recommend applying a minimum 50mm compacted

overlay for carpark areas. The topping should be applied

at a temperature of between 120-150?C.

ARDEX WPM 5000HD should be installed by approved

applicators well trained in the application of self-adhesive

membranes. Installation shall be strictly in accordance with

ARDEX recommendations.

 

 

 

SAFETY PRECAUTIONS

ARDEX WPM 5000HD is hazardous; non-dangerous goods.

Wear eye/face protection. Use only in well ventilated

areas. Keep rolls in a well ventilated place. In case of

contact with eyes rinse with plenty of water and contact a

doctor or Poisons Information Centre.

ARDEX WPM 249 is hazardous; non-dangerous goods. It is

highly flammable harmful if swallowed and irritating to the

eyes and skin. Keep away from sources of ignition. No

smoking. Keep container tightly closed and in a well

ventilated place.

ADDITIONAL INFORMATION FOR ARDEX WPM 249 IS

FOUND IN THE MATERIAL SAFETY DATA SHEET.

STORAGE

All rolls of ARDEX WPM 5000HD whether palletised or

loose should be stored in a cool covered area protected

against sunlight and UV radiation. Rolls should be stored in

a vertical position on a smooth floor so as not to damage

the edges.

ADDITIONAL INFORMATION IS LISTED IN THE MATERIAL

SAFETY DATA SHEET.

PACKAGING

Roll size: 1m x 20m

Roll weight: Approx 30kg.

Other products: ARDEX Shelterseal Primer 5 litres and

20 litres.

Rolls per pallet: 25